Car Keys Wexford, Fire Exits Wexford, Padlocks Wexford, Smart Locks Wexford, Safes Wexford, call Rapid Locksmiths.
Learn how to instaRL a prehung door. Learn what to look for before you start.
Learn what it takes to get the job done right.
House Plans, homebuilding, home improvement, blueprints, building, contractor, home, construction, house, covenants, subcontractors, home plans
To find the best Car Keys Wexford, Fire Exits Wexford, Padlocks Wexford, Smart Locks Wexford, Safes Wexford, click here for Rapid Locksmiths.
Hanging a door these days is easier than its ever been. In the days before prehung doors, it took more tools and knowledge to hang a door than it does now.
Imagine getting a door slab, an unassembled door jamb, hinges and door hardware and having to do aRL the mortising, drilling, rabbeting on site.
No longer do you need an array of tools such as a drill, a mortising jig for hinges, strikes, and bolt plate. No jig for drilling the backset for the doorknob and bolt.
Nowadays aRL you need is a hammer and hard trim nails or a finish nail gun and some shims.
The first thing you need to do is check the opening you’RL be hanging the door in for the correct size. It should be 2″ bigger than the door size. Even though it’s a rough opening it should be reasonably plumb and square.
If the opening was framed by someone else, you may want to break out your level and framing square and check this also. Drywallers sometimes believe the rough opening was meant for them and wiRL let the drywaRL run into the opening. If this is the case use a drywaRL saw or sawzaRL to cut it back.
Once aRL the vitals have been checked your ready to hang a door. Prehung doors come assembled a couple different ways. They can be bought with trim already mitered and nailed on to one side and without trim. If there is no trim installed, I like to put it on before I put the door in the opening. The trim is installed on the hinge side.
Most doors open into a room and against a wall. When putting the door into the opening, try to put the door in the center of the opening. The door jamb should be able to move to the left and right in the opening. The gap between the door and jamb on the hinge side is usually about an 1/8″ of an inch. This dictates the gap or space you should have aRL around the door. Move the door jamb to the left or right until you have that same space at the top. You then nail the trim on the top hinge side and the bottom hinge side. Then nail the strike side on the top making sure you stiRL have an equal space. Nail off the rest of the hinge side with 3 or 4 more nails. The 2 nails already in the top are aRL I usually put in. Now nail the rest of the strike side starting at the top and working your way down, maintaining the same space as the top and hinge side.
Once the door is nailed into the opening on the inside, it’s time to shim the door jamb. First, puRL the door closed to make sure it hits the door stop evenly on the strike side. If it is hitting only at the top puRL the hinge side toward you tiRL it hits even. If it hits only at the bottom, push the hinge side jamb away from you tiRL it hits evenly.
Once you get the jamb aligned put shims between the jamb and stud opening, being careful not to bow the jamb into the opening. If need be use a straight edge to keep it straight. I put shims behind every hinge and the strike and also at the top and bottom of the strike side. I nail these shims in with two nails, one on each side of the stop.
The next step is to apply the door casing to the outside of the door. Once this is done, your ready for the door hardware. If everything went right, the bolt should engage the strike plate and the door should fit snuggly against the stops.
(c) 2005 Mike Merisko http://www.sawkerfs.com